Preparation and structure of poly(vinyl alcohol)–poly(vinyl acetate) composite porous membrane

The preparation of poly(vinyl alcohol) (PVA)–poly(vinyl acetate) (PVAc) composite porous membrane was investigated by extracting PVAc with solvent from films of PVAc lattices which were obtained by the emulsion polymerization of vinyl acetate (VAc) in the presence of PVA. The formation of the porous membrane depended upon whether or not PVAc in the latex film was easily extracted with solvent. In the case of using hydrogen peroxide (HPO)–tartaric acid (TA) as an initiator, in the film of the latex which was produced from the batch method in which all ingredients of the batch were put into the reaction vessel before starting polymerization, PVAc could be extracted over 90% of total PVAc with common organic solvents. In the film of the latex which was produced from the dropwise addition method of VAc and initiator, the PVAc extraction was about 20-30%. On the other hand, in the case of using ammonium persulfate as an initiator, the desired porous membrane was not obtained. The structure of the porous membrane obtained from the latex of the batch method by using HPO—TA consisted of spherical cells which were made up of PVA and grafted PVAc or insoluble PVAc like microgels, which were not extracted with organic solvent and were connected by small pores. The PVA—PVAc composite porous membrane is permeated by n-hexane with 5.58 × 10² mL/cm²·s at 0.5 kg/cm², by benzene with only 1.33 × 10^?3mL/cm²·s even at 60 kg/cm².     

Lysozyme requires fluctuation of the active site for the manifestation of activity

Mutations around His15 which lie far away from the active site,stimulated glycol chitin activity of lysozyme at physiologicaltemperature. Del-Argl4Hisl5 lysozyme, a mutant lysozyme whoseArgl4 and Hisl5 were deleted together, and has the highest activityamong these mutant lysozymes, had a similar binding abilityto a trimer of N-acetyl-glucosamine, a substrate analogue, relativeto native lysozyme. This suggests that the increased activitywas due to an increased k_cat in the catalysis reaction. TheH-D exchange rate of the N-1 proton in the Trp63 which is locatedin the active site cleft, was enhanced in the Del-Argl4Hisl5lysozyme, while 2-D proton NMR analysis revealed no conformationalchange around Trp63. We conclude that some sort of fluctuationat the active site might be required for the manifestation ofactivity. This theory is supported by the finding that the Del-Argl4Hisl5lysozyme showed a shift in temperature dependency of activityto lower temperatures compared with that of native lysozyme.     

High oleic acid oil suppresses lung tumorigenesis in mice through the modulation of extracellular signal-regulated kinase cascade

This study was undertaken to estimate the effect of dietary high oleic acid oil (OA) on 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK)-induced lung tumorigenesis in mice. Diet containing 10% oil was fed to mice through experimental periods. On day 30 after NNK injection (100 mg/kg body weight, i.p.), the treatment increased the level of prostaglandin E₂ (PGE₂) as well as proliferating cell nuclear antigen, a marker of cell proliferation in a high linoleic acid oil (LA)-fed group but not in an OA-fed group. The NNK treatment also induced the activation of an extracellular signal-regulated kinase (Erk) cascade (Erk, Mek and Raf-1) in an LA-fed group. On the other hand, OA feeding abolished the NNK-induced activation of the Erk cascade. In conjugation with these events, OA feeding reduced lung tumor incidence and tumor multiplicity (percentage of mice with tumors) in mice compared with LA feeding at the 20th experimental week. These results suggest that OA suppresses lung tumorigenesis and that this suppression is correlated with the inhibition of PGE₂ production and inactivation of the Erk cascade.     

Electrochemical micromachining using a solid electrochemical reaction at the metal/β″-Al2O3 microcontact

A simple solid state technique for electrochemical micromachining of metal substrates using a metal ion conductor (Na-β″-Al₂O₃) was proposed. The fundamental solid electrochemical cell consists of a (anode) metal substrate (M = Ag, Cu, Zn, and Pb)/pyramidal Na-β″-Al₂O₃/Ag (cathode) system, where the contact diameter between M/Na-β″-Al₂O₃ was extremely small, on the order of a few micrometer. Under an applied electric field, the metal substrate was electrochemically oxidized to metal ions (Mⁿ⁺) at the M/Na-β″-Al₂O₃ microcontact. These Mⁿ⁺ ions migrated into the Na-β″-Al₂O₃. As a result of continuous electrolysis, the metal substrate was locally consumed at the microcontact, and thus solid state electrochemical micromachining was accomplished. As expected, the machining size or depth depended on the electrolysis conditions (current, operating time) and the apex configuration of pyramidal Na-β″-Al₂O₃. Moreover, the scanning of the Na-β″-Al₂O₃ pyramid during electrolysis produced a fine patterned metal substrate. In the present paper, solid state electrochemical micromachining was performed for several metal substrates, and its advantages and disadvantages vis-a-vis the conventional electrochemical micromachining method are discussed in detail.     

Sintering Kinetics at Isothermal Shrinkage: II, Effect of Y2O3 Concentration on the Initial Sintering Stage of Fine Zirconia Powder

The shrinkage behavior of fine zirconia powders containing 2.9 and 7.8 mol% Y₂O₃ was investigated to clarify the effect of Y₂O₃ concentration on the initial sintering stage. The shrinkage of powder compact was measured under both conditions of constant rates of heating (CRH) and constant temperatures. CRH measurements revealed that when the Y₂O₃ concentration of fine zirconia powder increased, the starting temperature of shrinkage shifted to a high temperature. Isothermal shrinkage measurements revealed that the increase in Y₂O₃ concentration causes the shrinkage rate to decrease. The values of activation energy ( Q ) and frequency-factor term (β₀) of diffusion at initial sintering were estimated by applying the sintering-rate equation to the isothermal shrinkage data. When the Y₂O₃ concentration increases, both Q and β₀ of diffusion increase. It is, therefore, concluded that the increase in Y₂O₃ concentration of fine zirconia powder decreases the shrinkage rate because of increasing Q of diffusion at the initial stage of sintering.     

Short- and long-term strength characteristics of particulate-filled cast epoxy resin

Particulate-filled thermosetting composites are widely used, yet little systematic work has been done on their long-term strength characteristics. In this study short-term tensile, flexural, and impact tests as well as tensile creep-rupture tests were made for unfilled and filled epoxy to clarify the effects of filler size, filler content, and temperature. Fillers used were silica, alumina particles, and glass beads. Test temperatures were varied from 25 to 110°C. As a result of short-term testing, it was found that the Petch relation held between strength and filler size if brittle fracture occurred, while a strength and filler size if brittle fracture occurred, while a strengthening effect existed when ductile fracture occurred. On creeprupture testing, a strengthening is observed with filler size and content for silica and glass beads. The Arrhenius plot of rupture time for various filler sizes and contents converges to a characteristic point corresponding to the glass transition temperature of the material. Using this relation, a modified Larson-Miller master rupture curve is proposed which can predict the long-term strength of particulate-filled thermosetting composites as functions of rupture time, temperature, filler size, and content.     

Relation between crystal structure and lattice oxygen content of sintered reaction-bonded silicon nitride

When reaction-bonded silicon nitride containing MgO/Y₂O₃ additives is sintered at three different temperatures to form sintered reaction-bonded silicon nitride (SRBSN), the thermal conductivity increases with sintering temperature. The β-Si₃N₄ (silicon nitride) crystals of SRBSN ceramics were synthesized and characterized to investigate the relation between the crystal structure and the lattice oxygen content. The hot-gas extraction measurement result and the crystal structure obtained using Rietveld analysis suggested that the unit cell size of the β-Si₃N₄ crystal increases with the decrease in the lattice oxygen content. This result is reasonable considering that the lattice oxygen with the smaller covalent radius substitutes nitrogen with the larger one in the β-Si₃N₄ crystals. The lattice oxygen content decreased with increasing sintering temperature which also correlated with increase in thermal conductivity. Moreover, it is noteworthy from the viewpoint that it may be possible to apply the lattice constant analysis for the nondestructive and simple measurement of the lattice oxygen content that deteriorates the thermal conductivity of the β-Si₃N₄ ceramics.     

Construction of living cellular automata using the Physarum plasmodium

The plasmodium of Physarum polycephalum is a unicellular and multinuclear giant amoeba that has an amorphous cell body. To clearly observe how the plasmodium makes decisions in its motile and exploratory behaviours, we developed a new experimental system to pseudo-discretize the motility of the organism. In our experimental space that has agar surfaces arranged in a two-dimensional lattice, the continuous and omnidirectional movement of the plasmodium was limited to the stepwise one, and the direction of the locomotion was also limited to four neighbours. In such an experimental system, a cellular automata-like system was constructed using the living cell. We further analysed the exploratory behaviours of the plasmodium by duplicating the experimental results in the simulation models of cellular automata. As a result, it was revealed that the behaviours of the plasmodium are not reproduced by only local state transition rules; and for the reproduction, a kind of historical rule setting is needed.     

Cost-Efficient Traffic Aggregation Employing Cross-Layer Shared Protection

Shared protection/restoration is a promising solution for reducing protection resources and is supported at each layer of the current multi-layer networks. Software-defined networking is expected to reduce equipment cost as well as operational cost by orchestrating these shared protection functionalities. However, although protection resource sharing improves link utilization, it sometimes increases the required equipment. Meanwhile, traffic re-aggregation at each layer is an important technique for low volume traffic to utilize the underlying link capacity more efficiently, but re-aggregation also makes it difficult to share protection resources with traffic at lower layers. In this paper, we present multi-layer network design strategy and method that reduce equipment cost by means of both traffic re-aggregation at each layer and protection resource sharing among multiple service traffic at different layers. The strategy first prioritizes traffic re-aggregation at each layer, and then maximally delegates shared protection to lower layers as long as it does not increase the required capacity at the lower layer. Evaluation results from the example three-layer networks confirm that the proposed method can effectively reduce equipment cost compared to the conventional design method. Cost reduction is achieved by leveraging shared protection functions at multiple layers.